Section 21.142

14 CFR Ch. I (1-1-19 Edition)

complies with the requirements of this
subpart.
Section 21.142 Production limitation record.
The FAA issues a production limitation record as part of a production certificate. The record lists the type certificate number and model of every
product that the production certificate
holder is authorized to manufacture,
and identifies every interface component that the production certificate
holder is authorized to manufacture
and install under this part.
[Doc. No. FAA-2013-0933, Amdt. 21-98, 80 FR
59031, Oct. 1, 2015, as amended by Amdt. 21-
98A, 80 FR 59031, Dec. 17, 2015]

Section 21.143 Duration.
A production certificate is effective
until surrendered, suspended, revoked,
or the FAA otherwise establishes a termination date.

spaschal on DSK3GDR082PROD with CFR

Section 21.144 Transferability.
The holder of a production certificate
may not transfer the production certificate.
Section 21.145 Privileges.
(a) The holder of a production certificate may - 
(1) Obtain an aircraft airworthiness
certificate without further showing,
except that the FAA may inspect the
aircraft for conformity with the type
design; or
(2) In the case of other products, obtain approval from the FAA for installation on type-certificated aircraft.
(b) Notwithstanding the provisions of
Section 147.3 of this chapter, the holder of a
production certificate for a primary
category aircraft, or for a normal, utility, or acrobatic category aircraft of a
type design that is eligible for a special
airworthiness certificate in the primary category under Section 21.184(c), may - 
(1) Conduct training for persons in
the performance of a special inspection
and preventive maintenance program
approved as a part of the aircraft-s
type design under Section 21.24(b), provided a
person holding a mechanic certificate
with appropriate airframe and powerplant ratings issued under part 65 of
this chapter gives the training; and
(2) Issue a certificate of competency
to persons successfully completing the

approved training program, provided
the certificate specifies the aircraft
make and model to which the certificate applies.
Section 21.146

Responsibility of holder.

The holder of a production certificate
must - 
(a) Amend the document required by
Section 21.135 as necessary to reflect changes
in the organization and provide these
amendments to the FAA.
(b) Maintain the quality system in
compliance with the data and procedures approved for the production certificate;
(c) Ensure that each completed product or article for which a production
certificate has been issued, including
primary category aircraft assembled
under a production certificate by another person from a kit provided by the
holder of the production certificate,
presented for airworthiness certification or approval conforms to its approved design and is in a condition for
safe operation;
(d) Mark the product or article for
which a certificate or approval has
been issued. Marking must be in accordance with part 45 of this chapter,
including any critical parts;
(e) Identify any portion of the product or article (e.g., sub-assemblies,
component parts, or replacement articles) that leave the manufacturer-s facility as FAA approved with the manufacturer-s part number and name,
trademark, symbol, or other FAA approved manufacturer-s identification;
(f) Have access to type design data
necessary to determine conformity and
airworthiness for each product and article produced under the production
certificate;
(g) Retain its production certificate
and make it available to the FAA upon
request; and
(h) Make available to the FAA information regarding all delegation of authority to suppliers.
Section 21.147 Amendment of production certificates.
(a) A holder of a production certificate must apply for an amendment to a
production certificate in a form and
manner prescribed by the FAA.

158

VerDate Sep<11>2014

12:50 Apr 30, 2019

Jkt 247046

PO 00000

Frm 00168

Fmt 8010

Sfmt 8002

Y:\SGML\247046.XXX

247046