Section 60.11

14 CFR Ch. I (1-1-19 Edition)

the Statement of Qualification that
may be accessed by an appropriate terminal or display in or adjacent to the
FSTD is satisfactory.
(c) Each sponsor of an FSTD must
identify to the NSPM by name, one individual to be the management representative (MR).
(1) One person may serve as an MR
for more than one FSTD, but one
FSTD must not have more than one
person serving in this capacity.
(2) Each MR must be an employee of
the sponsor with the responsibility and
authority to - 
(i) Monitor the on-going qualification
of assigned FSTDs to ensure that all
matters regarding FSTD qualification
are being carried out as provided for in
this part;
(ii) Ensure that the QMS is properly
established, implemented, and maintained by overseeing the structure (and
modifying where necessary) of the QMS
policies, practices, and procedures; and
(iii) Regularly brief sponsor-s management on the status of the on-going
FSTD qualification program and the
effectiveness and efficiency of the
QMS.
(3) The MR serves as the primary
contact point for all matters between
the sponsor and the NSPM regarding
the qualification of that FSTD as provided for in this part.
(4) The MR may delegate the duties
described in paragraph (c)(2) and (c)(3)
of this section to an individual at each
of the sponsor-s locations.

kpayne on VMOFRWIN702 with $$_JOB

Section 60.11

result of continually meeting the requirements of this part.
(b) Is qualified as described in the
Statement of Qualification.
(c) Remains qualified, through satisfactory inspection, continuing qualification evaluations, appropriate maintenance, and use requirements in accordance with this part and the applicable QPS.
(d) Functions during day-to-day
training, evaluation, or flight experience activities with the software and
hardware that was evaluated as satisfactory by the NSPM and, if modified,
modified only in accordance with the
provisions of this part. However, this
section does not apply to routine software or hardware changes that do not
fall under the requirements of Section 60.23.
(e) Is operated in accordance with the
provisions and limitations of Section 60.25.
Section 60.13 FSTD objective data requirements.
(a) Except as provided in paragraph
(b) and (c) of this section, for the purposes of validating FSTD performance
and handling qualities during evaluation for qualification, the data made
available to the NSPM (the validation
data package) must include the aircraft manufacturer-s flight test data
and all relevant data developed after
the type certificate was issued (e.g.,
data developed in response to an airworthiness directive) if such data results from a change in performance,
handling qualities, functions, or other
characteristics of the aircraft that
must be considered for flight crewmember training, evaluation, or for
meeting experience requirements of
this chapter.
(b) The validation data package may
contain flight test data from a source
in addition to or independent of the
aircraft manufacturer-s data in support
of an FSTD qualification, but only if
this data is gathered and developed by
that source in accordance with flight
test methods, including a flight test
plan, as described in the applicable
QPS.
(c) The validation data package may
also contain predicted data, engineering simulation data, data from pilot
owner or pilot operating manuals, or

FSTD use.

No person may use or allow the use
of or offer the use of an FSTD for flight
crewmember training or evaluation or
for obtaining flight experience to meet
any of the requirements under this
chapter unless, in accordance with the
QPS for the specific device, the FSTD
meets all of the following:
(a) Has a single sponsor who is qualified under Section 60.7. The sponsor may arrange with another person for services
of document preparation and presentation, as well as FSTD inspection,
maintenance, repair, and servicing;
however, the sponsor remains responsible for ensuring that these functions
are conducted in a manner and with a

8

VerDate Sep<11>2014

16:30 Jun 25, 2019

Jkt 247047

PO 00000

Frm 00018

Fmt 8010

Sfmt 8010

Q:\14\14V2.TXT

PC31