Federal Aviation Administration, DOT

Section 135.25

(iii) Handling;
(iv) Storage incidental to transport;
(v) Packaging of company material;
or
(vi) Loading.
(2) Ensure that the procedures and
information described in this paragraph are sufficient to assist a person
in identifying packages that are
marked or labeled as containing hazardous materials or that show signs of
containing undeclared hazardous materials. The procedures and information
must include:
(i) Procedures for rejecting packages
that do not conform to the Hazardous
Materials Regulations in 49 CFR parts
171 through 180 or that appear to contain undeclared hazardous materials;
(ii) Procedures for complying with
the hazardous materials incident reporting requirements of 49 CFR 171.15
and 171.16 and discrepancy reporting requirements of 49 CFR 175.31.
(iii) The certificate holder-s hazmat
policies and whether the certificate
holder is authorized to carry, or is prohibited from carrying, hazardous materials; and
(iv) If the certificate holder-s operations specifications permit the transport of hazardous materials, procedures
and information to ensure the following:
(A) That packages containing hazardous materials are properly offered
and accepted in compliance with 49
CFR parts 171 through 180;
(B) That packages containing hazardous materials are properly handled,
stored, packaged, loaded and carried on
board an aircraft in compliance with 49
CFR parts 171 through 180;
(C) That the requirements for Notice
to the Pilot in Command (49 CFR
175.33) are complied with; and
(D) That aircraft replacement parts,
consumable materials or other items
regulated by 49 CFR parts 171 through
180 are properly handled, packaged, and
transported.
(q) Procedures for the evacuation of
persons who may need the assistance of
another person to move expeditiously
to an exit if an emergency occurs; and
(r) If required by Section 135.385, an approved Destination Airport Analysis
establishing runway safety margins at
destination airports, taking into ac-

count the following factors as supported by published aircraft performance data supplied by the aircraft manufacturer for the appropriate runway
conditions - 
(1) Pilot qualifications and experience;
(2) Aircraft performance data to include normal, abnormal and emergency
procedures as supplied by the aircraft
manufacturer;
(3) Airport facilities and topography;
(4) Runway conditions (including
contamination);
(5) Airport or area weather reporting;
(6) Appropriate additional runway
safety margins, if required;
(7) Airplane inoperative equipment;
(8) Environmental conditions; and
(9) Other criteria affecting aircraft
performance.
(s) Other procedures and policy instructions regarding the certificate
holder-s operations issued by the certificate holder.
[Doc. No. 16097, 43 FR 46783, Oct. 10, 1978, as
amended by Amdt. 135-20, 51 FR 40709, Nov. 7,
1986; Amdt. 135-58, 60 FR 65939, Dec. 20, 1995;
Amdt. 135-91, 68 FR 54586, Sept. 17, 2003;
Amdt. 135-101, 70 FR 58829, Oct. 7, 2005]

Section 135.25 Aircraft requirements.
(a) Except as provided in paragraph
(d) of this section, no certificate holder
may operate an aircraft under this part
unless that aircraft - 
(1) Is registered as a civil aircraft of
the United States and carries an appropriate and current airworthiness certificate issued under this chapter; and
(2) Is in an airworthy condition and
meets the applicable airworthiness requirements of this chapter, including
those relating to identification and
equipment.
(b) Each certificate holder must have
the exclusive use of at least one aircraft that meets the requirements for
at least one kind of operation authorized in the certificate holder-s operations specifications. In addition, for
each kind of operation for which the
certificate holder does not have the exclusive use of an aircraft, the certificate holder must have available for use
under a written agreement (including
arrangements for performing required
maintenance) at least one aircraft that
meets the requirements for that kind

413

VerDate Sep<11>2014

08:20 May 17, 2019

Jkt 247048

PO 00000

Frm 00423

Fmt 8010

Sfmt 8002

Y:\SGML\247048.XXX

247048