Section 172.102 49 CFR Ch. I (10-1-18 Edition) inhalation hazard under the provisions of this subchapter. 3 This material is poisonous by inhalation (see Section 171.8 of this subchapter) in Hazard Zone C (see Section 173.116(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter. 4 This material is poisonous by inhalation (see Section 171.8 of this subchapter) in Hazard Zone D (see Section 173.116(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter. 5 If this material meets the definition for a material poisonous by inhalation (see Section 171.8 of this subchapter), a shipping name must be selected which identifies the inhalation hazard, in Division 2.3 or Division 6.1, as appropriate. 6 This material is poisonous-by-inhalation and must be described as an inhalation hazard under the provisions of this subchapter. 8 A hazardous substance that is not a hazardous waste may be shipped under the shipping description - Other regulated substances, liquid or solid, n.o.s. - , as appropriate. In addition, for solid materials, special provision B54 applies. 9 Packaging for certain PCBs for disposal and storage is prescribed by EPA in 40 CFR 761.60 and 761.65. 11 The hazardous material must be packaged as either a liquid or a solid, as appropriate, depending on its physical form at 55 SectionC (131 SectionF) at atmospheric pressure. 12 In concentrations greater than 40 percent, this material has strong oxidizing properties and is capable of starting fires in contact with combustible materials. If appropriate, a package containing this material must conform to the additional labeling requirements of Section 172.402 of this subchapter. 13 The words - Inhalation Hazard - shall be entered on each shipping paper in association with the shipping description, shall be marked on each non-bulk package in association with the proper shipping name and identification number, and shall be marked on two opposing sides of each bulk package. Size of marking on bulk package must conform to Section 172.302(b) of this subchapter. The requirements of SectionSection 172.203(m) and 172.505 of this subchapter do not apply. 14 Motor fuel antiknock mixtures are: a. Mixtures of one or more organic lead mixtures (such as tetraethyl lead, triethylmethyl lead, diethyldimethyl lead, ethyltrimethyl lead, and tetramethyl lead) with one or more halogen compounds (such as ethylene dibromide and ethylene dichloride), hydrocarbon solvents or other equally efficient stabilizers; or b. tetraethyl lead. 15 This entry applies to - Chemical kits - and - First aid kits - containing one or more compatible items of hazardous materials in boxes, cases, etc. that, for example, are used for medical, analytical, diagnostic, testing, or repair purposes. Kits that are carried on board transport vehicles for first aid or operating purposes are not subject to the requirements of this subchapter. 16 This description applies to smokeless powder and other solid propellants that are used as powder for small arms and have been classed as Division 1.3C, 1.4C and Division 4.1 in accordance with Section 173.56 of this subchapter. 19 For domestic transportation only, the identification number - UN1075 - may be used in place of the identification number specified in column (4) of the Section 172.101 table. The identification number used must be consistent on package markings, shipping papers and emergency response information. 21 This material must be stabilized by appropriate means (e.g., addition of chemical inhibitor, purging to remove oxygen) to prevent dangerous polymerization (see Section 173.21(f) of this subchapter). 22 If the hazardous material is in dispersion in organic liquid, the organic liquid must have a flash point above 50 SectionC (122 SectionF). 23 This material may be transported under the provisions of Division 4.1 only if it is so packed that the percentage of diluent will not fall below that stated in the shipping description at any time during transport. Quantities of not more than 500 g per package with not less than 10 percent water by mass may also be classed in Division 4.1, provided a negative test result is obtained when tested in accordance with test series 6(c) of the UN Manual of Tests and Criteria (IBR, see Section 171.7 of this subchapter). 24 Alcoholic beverages containing more than 70 percent alcohol by volume must be transported as materials in Packing Group II. Alcoholic beverages containing more than 24 percent but not more than 70 percent alcohol by volume must be transported as materials in Packing Group III. 26 This entry does not include ammonium permanganate, the transport of which is prohibited except when approved by the Associate Administrator. 28 The dihydrated sodium salt of dichloroisocyanuric acid does not meet the criteria for inclusion in Division 5.1 (Oxidizer) and is not subject to the requirements of this subchapter unless meeting the criteria for inclusion in another class or division. 30 Sulfur is not subject to the requirements of this subchapter if transported in a nonbulk packaging or if formed to a specific shape (for example, prills, granules, pellets, pastilles, or flakes). A bulk packaging 344 VerDate Sep<11>2014 16:41 Oct 31, 2018 Jkt 244226 PO 00000 Frm 00354 Fmt 8010 Sfmt 8010 Q:\49\49V2.TXT PC31